Ultra Short Throw Projector
WXGA 2600 ANSI
|Power Supply||100 - 240 V AC, 50 / 60 Hz|
|Power Consumption||310 W (0.5 W when STANDBY MODE set to ECO,*¹ 6.0 W when STANDBY MODE set to NORMAL.*²)|
|DLP™ Chip||Panel Size||16.5 mm (0.65 in) diagonal (16:10 aspect ratio)|
|Display Method||DLP™ chip x 1 DLP™ system|
|Pixels||1,024,000 (1,280 x 800) pixels|
|Lens||Fixed (0.35:1 throw ratio), manual focus F = 2.6, f = -5.27 mm|
|Lamp||240 W UHM lamp (The lamp replacement cycle is 5,000 hours*³)|
|Screen Size (diagonal)||1.78-2.54 m (70-100 in)
(16:10 aspect ratio)
|Colour Reproducibility||Full colour (16,777,216 colours)|
|Center-to-corner uniformity*⁴||80 %|
|Contrast*⁴||8,000:1 (full on / off) (During RGB signal input, lamp power: Normal)|
|Resolution||1,280 x 800 pixels
(Input signals that exceed this resolution will be converted to 1,280 x 800 pixels.)
|Scanning Frequency||HDMI||(Horizontal) 15-100 kHz; (Vertical) 24-120 Hz; (Dot clock) 25-162 MHz|
|RGB (analogue)||(Horizontal) 15-100 kHz; (Vertical) 24-120 Hz; (Dot clock) 162 MHz or lower|
|YPBPR (YCBCR)||fH: 15.75 kHz, fV: 60 Hz [480i (525i)]
fH: 31.50 kHz, fV: 60 Hz [480p (525p)]
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i]
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p]
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
fH: 15.63 kHz, fV: 50 Hz [576i (625i)]
fH: 31.25 kHz, fV: 50 Hz [576p (625p)]
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p]
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i]
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p]
|Video / S-Video||(fH) 15.75 / 15.63 kHz (fV) 50 / 60 Hz [NTSC / NTSC4.43 / PAL / PAL60 / PAL-N / PAL-M / SECAM]|
|Keystone Correction Range||Vertical: ±15°|
|Installation||Ceiling / floor, front / rear (Menu setting)|
|Built-in Speaker||7cm x 3cm oval shape x 1, output power 10 W (monaural)|
|Terminals||HDMI IN||HDMI 19-pin x 1(Deep colour, compatible with HDCP),
audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
|COMPUTER IN 1||D-sub HD 15-pin (female) x 1 [RGB / YPB(CB) / PR (CR) x 1]|
|COMPUTER IN 2||D-sub HD 15-pin (female) x 1 [RGB / YPB(CB) / PR (CR) x 1]|
|MONITOR OUT||D-sub HD 15-pin (female) x 1 (The signal selected from computer input 1/2 is output.)|
|VIDEO IN||Pin jack x 1|
|S-VIDEO IN||Mini DIN 4-pin x 1|
|COMPUTER 1 AUDIO IN||M3 x 1 (L-R x 1)|
|COMPUTER 2 AUDIO IN||M3 x 1 (L-R x 1)|
|VIDEO AUDIO IN||Pin jack x 2 (L x 1, R x 1)|
|S-VIDEO AUDIO IN||Pin jack x 2 (L x 1, R x 1)|
|AUDIO OUT||M3 x 1 (L-R x 1) (variable)|
|SERIAL IN||D-sub 9-pin (female) x 1 for external control (RS-232C compliant)|
|LAN||RJ-45 x 1 (for network connection, 100BASE-TX / 10BASE-T, compliant with PJLink™ (class 1))|
|Mini USB||1 for servicemen (for interactive function*5)|
|Power Cord Length||3.0 m (9'10")|
|Cabinet Materials||Molded plastic (PC)|
|Dimensions (W x H x D)||357 x 250 x 367 mm (14-1/16 x 9-27/32 x 14-29/64 in)
(with legs at shortest position)
|Weight||Approximately 7.5 kg (16.5 lbs)*6|
|Noise Level*4||35 dB (Lamp power: Normal);
30 dB (Lamp power: Eco)
|Operating Temperature||5°C-40°C [41°F-104°F] (Less than 762 m [2,500 ft] above sea level);
5°C-35°C [41°F-95°F] (between 762 and 1,524 m [2,500 ft and 5,000 ft] above sea level);
5°C-30°C [41°F-86°F] (between 1,524 and 3,048 m [5,000 ft and 10,000 ft] above sea level)
|Operating Humidity||20 % - 80 % (no condensation)|
|Supplied Accessories||Power cord x 1( x 2 for PT-CW330EA, PT-CW240EA, PT-CX300EA), power cord cover x 1,
wireless remote control unit x 1, battery for remote control (lithium coin cell type x 1),
computer cable (1.8 m, for VGA) x 1
|NOTE||* Product numbers vary depending on the market. The general guideline is as follows:
The product number in the Americas and Taiwan is PT-CW331RU, PT-CW330U, PT-CW241RU, PT-CW240U, PT-CX301RU and PT-CX300U.
The product number in Europe (except the UK) and CIS is PT-CW331RE, PT-CW330E, PT-CW241RE, PT-CW240E, PT-CX301RE and PT-CX300E.
The product number in the UK, Asia (except Taiwan), Oceania, Middle East, and Africa is PT-CW331REA, PT-CW330EA, PT-CW241REA, PT-CW240EA, PT-CX301REA and PT-CX300EA.
*1 When [LAN (Standby)] / [VGA Out (Standby)]/[In Standby Mode (Audio)] are all set to [Off].
*2 When [LAN (Standby)] / [VGA Out (Standby)]/[In Standby Mode (Audio)] are all set to [On].
*3 This is the maximum value when the lamp power is set to Eco mode where the lamp is turned on for 2 hours and off for 0.25 hours. If the lamp is turned on more times or kept on for a long time, the lamp replacement cycle will shorten. In Normal mode, the lamp replacement cycle is 3,500 hours for the PT-CW241R/CW240 and 3,000 hours for the PT-CW331R/CW330/CX301R/CX300. The usage environment affects the duration of the lamp.
*4 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*5 Exclusively for PT-CW331R / CW241R / CX301R.
*6 The above values are averages. Actual values may be different according to the product.
|NOTES ON USE||1 The projector uses a high-voltage mercury lamp under high internal pressure. This lamp may break, emitting a popping sound, or fail to illuminate, due to impact or extended use.
2 The high-wattage lamp becomes very hot during operation. Please observe the following precautions:
• Never place objects on top of the projector while it is in operation.
• Make sure there is an unobstructed space of 500 mm (19-11/16 in) or more around the projector’s exhaust openings.
• If stacking projector units, care must be taken to provide the recommended space between units. These space requirements also apply to installation where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must match the operating temperature listed in the specifications table during use. Also, make sure the projector’s intake and exhaust openings are not blocked. Ensure there is sufficient ventilation to prevent hot air from the exhaust openings being recirculated into the intake opening.
3 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions.
• The brightness of the lamp will gradually decrease with use.
4 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lamp performance.